| The XAP® 400 audio management and distribution device combines the great features of the XAP 800 with a single-line analog telephone interface and 10W amplifier to create a stand-alone teleconferencing unit. |
| |
ClearOne XAP 400 Specifications |
| Audio Performance |
| Conditions | Unless otherwise specified, all measurements are performed with a 22 Hz to 22kHz BW limit (no weighting) |
| Frequency Response | 20 Hz to 20 kHz ±1 dB |
| Noise (EIN) | -126 dBu, 20 kHz BW, max gain, Rs = 150˛ |
| THD+N | <0.02% |
| SNR | 80 dB re 0 dBu, (A-weighted) |
| Dynamic Range | 100 dB (A-weighted) |
| Crosstalk | <-91 dB re 20 dBu @ 20 kHz channel to channel |
| Auto Mixer |
| Parameters | Number of Open Microphones (NOM) |
| PA Adaptive Mode |
| First Mic Priority Mode |
| Last Mic Mode |
| Maximum # of Mics Mode |
| Ambient Level |
| Gate Threshold Adjust |
| Off Attenuation Adjust |
| Hold Time |
| Decay Rate |
| Matrix Mixing |
| Parameters | 25 * 26 matrix |
| 8 analog in/out |
| 1 speaker out (10W) |
| 12 expansion bus in/out |
| 4 assignable processing blocks in/out |
| 1 telco in/out |
| Assignable Processing Blocks |
| Filters | All pass |
| Low pass |
| High pass |
| Low shelving |
| High shelving |
| Parametric EQ |
| Notch |
| CD Horn |
| Crossovers | Bessel |
| Butterworth |
| Linkwitz-Riley |
| Compressor |
| Delay adjustable up to 500 ms |
| Microphone Input |
| Configuration | Input Gain Adjust |
| Mic or Line Level |
| Phantom Power on/off |
| Echo Cancellation on/off |
| Noise Cancellation on/off |
| Filters | All Pass |
| Low Pass |
| High Pass |
| Notch |
| PEQ |
| Mute | on/off |
| Chairman Override | on/off |
| AGC | on/off |
| Speech Leveler | on/off |
| Auto Gate / Manual gate | |
| Adaptive Ambient | on/off |
| Mic/Line Inputs 1-4 |
| Push-on terminal block, balanced, bridging |
| Impedance | 5 k˛ |
| Nominal Level | adjustable -55 dBu, -25 dBu, 0 dBu |
| Maximum Level | -35 dBu, -5 dBu, +20 dBu |
| Echo Cancellation | 130 ms tail time (works with 12 dB of room gain) |
| Noise Cancellation | 6–15 dB attenuation |
| Phantom Power | 24 V, selectable |
| Line Inputs 5-8 |
| Push-on terminal block, balanced, bridging |
| Impedance | >10 k˛ |
| Nominal Level | 0 dBu |
| Maximum Level | 20 dBu |
| Outputs 1-8 |
| Push-on terminal block, balanced |
| Impedance | 50 ˛˛ |
| Nominal Level | 0 dBu |
| Maximum Level | 20 dBu |
| Telco Line |
| Type | RJ-11 POTS or analogue extension from a PBX |
| Expansion Bus In/Out |
| Proprietary Network | RJ-45 (2), 115.2 kbps, 110k ˛ impedance |
| Category five twisted-pair |
| Maximum cable length between any two units | 80' (24 metres) |
| RS-232 |
| Type | DB-9 female 9,600/19,200/38,400 |
| Default | 57,600 baud rate; 8 bits, 1 stop, no parity Hardware flow control on (default)/off |
| Control/Status |
| Type | DB25 female A/B (2) Inputs A/B:active low (pull to ground) |
| Outputs A/B | open collector, 40 VDC max, 40 mA each +5 VDC pins (2) (300 mA over-current protected) |
| Remote Panels A/B |
| 4-pin push-on terminal block |
| RS-485 proprietary protocol Category five twisted-pair cable |
| 1 pair data, 1 pair power and ground +15 VDC (300 mA over-current protected) |
| Set-up Software |
| G-Ware |
| Power |
| Input Range | Auto-adjusting |
| 100–240 VAC; 50/60 Hz |
| Power Consumption | 30 W typical |
| Dimensions (L x D x H) | 17.25" x 10.25" x 1.75" |
| 43.8 x 26 x 4.5 cm |
| Weight | 7 lb/3.2 kg dry |
| 12 lb/5.5 kg shipping |
| Operating Temperature | 32 to 100° F/0 to 38° C |
| Humidity | 15% to 80%, non-condensing |
| Approvals | FCC, CSA, IC, CE, NOM, ACA, SABS, JATE |
)
